Examples of home built speedbag platforms

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Speedbag
    replied
    Originally posted by JohnnieBoy View Post
    Hi there, I'm new to the forum and thought I would add my project to the thread and express my appreciation for some of the ideas posted here by the other users. I've never used a bag before but thought it would be a welcome addition to our gym downstairs. Given that I'm of a frugal sort and a carpenter by trade, I figured that with the right inspiration and tools a decent, solid platform could be fashioned out of the various bits and bobs in my workshop.

    The metal frame was made out of two 10' lengths of galvanized 'punched angle iron'. I cleaned them up and spray-painted them with galvanized primer and then gloss-black. The uprights are screwed to my wall studs, which are spaced 16" on-centre, with two 2 1/2" long #12 sized screws per upright. Knowing the spacing of your studs is important to know when you later on attach the supports to the platform.

    I took the opportunity to make a circle-cutting jig for my handheld router (look it up on the internet or Woodsmith 'Router Workshop' magazine) and made two 24" diameter circles out of 3/4" MDF. I Gorilla glued and clamped them together and used some 1 1/4" drywall screws (6 per side, spaced equally apart) to ensure a solid fit. The next morning I beltsanded smooth the edge of the now 1 1/2" thick disc and proceed to rough cut some red laminate/Formica/Arborite I had left over from a previous job. Once I had contact-cemented the material to the disc and given it a couple hours to cure, I laminate trimmed it with a router and prepared to attach the supports.

    You have to space the supports so that when it is all assembled, it will be easy to hook the top (ie. the diagonal portion), thread on your wingnuts, and then slip your bolts in on the bottom (ie. the horizonal portion) and secure with another set of wingnuts. For attaching the platform, I countersunk the bolt and washer from the underside so that the nut heads won't damage the speed bag in one of my future flurries. The back edge of the platform is approximately 1" from the wall. The swivel is attached in the centre with four 1 3/4" #8 screws.

    After the platform is put into position, the bag is attached and I put a sand bag on top to cut down on any vibration.

    Hope you like the pictures (I had to resize them to fit per the posting guidelines), as I'm very pleased with the outcome. I started on a Saturday morning, and with trying to bargain shop for the various pieces to no-avail, making my router jig, and otherwise doing the job right, I got the job done by Sunday evening. It could have been done in a day without painting the angle iron, doing the laminate, and just jig-sawing a circle.

    Cost: angle iron ($20 cdn), nuts, washers, bolts ($5 cdn), spray paint ($8). If you have to buy a sheet of 3/4" MDF, it may cost around $25 for a 4'x8' sheet. The laminate, I'm not sure off-hand. The swivel was $16 at Wal-mart, and the bag around $35.
    Man, that is a really nice (and original) looking unit. I have several professional, purchased boards from Ringside Boxing that have that red lamination on them, and they don't look one bit better than yours. I'm always getting emails about "making a home unit" and I think yours tops the list of simplicity, easy of finding material, and construction plan. Great Job, JohnnieBoy!

    Leave a comment:


  • JohnnieBoy
    replied
    Another Example

    Hi there, I'm new to the forum and thought I would add my project to the thread and express my appreciation for some of the ideas posted here by the other users. I've never used a bag before but thought it would be a welcome addition to our gym downstairs. Given that I'm of a frugal sort and a carpenter by trade, I figured that with the right inspiration and tools a decent, solid platform could be fashioned out of the various bits and bobs in my workshop.

    The metal frame was made out of two 10' lengths of galvanized 'punched angle iron'. I cleaned them up and spray-painted them with galvanized primer and then gloss-black. The uprights are screwed to my wall studs, which are spaced 16" on-centre, with two 2 1/2" long #12 sized screws per upright. Knowing the spacing of your studs is important to know when you later on attach the supports to the platform.

    I took the opportunity to make a circle-cutting jig for my handheld router (look it up on the internet or Woodsmith 'Router Workshop' magazine) and made two 24" diameter circles out of 3/4" MDF. I Gorilla glued and clamped them together and used some 1 1/4" drywall screws (6 per side, spaced equally apart) to ensure a solid fit. The next morning I beltsanded smooth the edge of the now 1 1/2" thick disc and proceed to rough cut some red laminate/Formica/Arborite I had left over from a previous job. Once I had contact-cemented the material to the disc and given it a couple hours to cure, I laminate trimmed it with a router and prepared to attach the supports.

    You have to space the supports so that when it is all assembled, it will be easy to hook the top (ie. the diagonal portion), thread on your wingnuts, and then slip your bolts in on the bottom (ie. the horizonal portion) and secure with another set of wingnuts. For attaching the platform, I countersunk the bolt and washer from the underside so that the nut heads won't damage the speed bag in one of my future flurries. The back edge of the platform is approximately 1" from the wall. The swivel is attached in the centre with four 1 3/4" #8 screws.

    After the platform is put into position, the bag is attached and I put a sand bag on top to cut down on any vibration.

    Hope you like the pictures (I had to resize them to fit per the posting guidelines), as I'm very pleased with the outcome. I started on a Saturday morning, and with trying to bargain shop for the various pieces to no-avail, making my router jig, and otherwise doing the job right, I got the job done by Sunday evening. It could have been done in a day without painting the angle iron, doing the laminate, and just jig-sawing a circle.

    Cost: angle iron ($20 cdn), nuts, washers, bolts ($5 cdn), spray paint ($8). If you have to buy a sheet of 3/4" MDF, it may cost around $25 for a 4'x8' sheet. The laminate, I'm not sure off-hand. The swivel was $16 at Wal-mart, and the bag around $35.
    Attached Files

    Leave a comment:


  • VJ87
    replied
    Updated pics:





    Leave a comment:


  • VJ87
    replied























    Just found this thread, will post more updated pics of it with 8 coats of poly-urethane stain pics above show 1 coat. Setup cost around 24~ bux. Speed bag 29.99, and hinge 19.99.

    Leave a comment:


  • atgatt
    replied
    ninja420,

    I bet that thin wood will crack after only a few hits.

    Good lookin' platform.

    Leave a comment:


  • Speedbag
    replied
    Originally posted by ninja420 View Post
    Hey guys I thought you might like to see pictures of the new platform I was contracted lol to build for my freind Pat. its just a regular ibox type frame with a 2-1/2" x 27" drum made from three 10' redwood 4x3s.

    That is a beautiful board. I bet it will sound really nice.

    Leave a comment:


  • ninja420
    replied
    BIG RED speedbag platform

    Hey guys I thought you might like to see pictures of the new platform I was contracted lol to build for my freind Pat. its just a regular ibox type frame with a 2-1/2" x 27" drum made from three 10' redwood 4x3s.
    Attached Files

    Leave a comment:


  • Speedbag
    replied
    Originally posted by juanantoniomartin View Post
    I scrounged some 3 inch angle iron and for a case of beer the fitters welded this up for me. The drum is 2 pieces of plywood glued together. With 10lbs of lead on the top it is super solid and fast. The other setup I made for my boy actually cost more to build!

    Very nice setup. Man, that looks solid.

    Leave a comment:


  • juanantoniomartin
    replied
    My new platform

    I scrounged some 3 inch angle iron and for a case of beer the fitters welded this up for me. The drum is 2 pieces of plywood glued together. With 10lbs of lead on the top it is super solid and fast. The other setup I made for my boy actually cost more to build!
    Attached Files

    Leave a comment:


  • Chris M
    replied
    What tools you need depend on the materials you're using.

    If you're making one out of 2x4's or even 4x4's with a double thickness of 3/4" plywood, I think you could get by just fine with a miter saw, a jigsaw, and a cordless drill for screws.

    If you want a metal frame, a cheap mig welder or arc welder, and a sawzall out to be sufficient. You'll still need the jigsaw to cut the drum out of the plywood though.

    Leave a comment:


  • metaldad
    replied
    What tools did you need? I'm getting tired of my stand, just broke the hook that holds the heavy bag, and my platform is definitely too thin but I make do for now. I'm really considering building a platfrom and hanging my heavy bag from the ceiling
    Last edited by metaldad; 07-23-2007, 10:47 AM. Reason: to get all i wanted to say in one quote

    Leave a comment:


  • ninja420
    replied
    I built it.

    Leave a comment:


  • Pegasos
    replied
    Really looks nice ninja420...

    good job,

    where did you get the frame by the way?

    Leave a comment:


  • Speedbag
    replied
    Originally posted by ninja420 View Post
    I finaly got some time so I built my self a platform for my room. And let me tell you guys it is GREAT! The board is a 1 inch pine round and a 1 inch oak table top. The frame is just a box made from 1 1/2" square tube so simple it hurts. There is no sand on it right now and it dosent vibrate at all! even with that huge bag.
    Now THAT'S a nice speed bag unit.

    Leave a comment:


  • ninja420
    replied
    one more picture
    Attached Files

    Leave a comment:

Speedbagforum.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Working...